A Step-by-Step Overview to Installing a Bathtub
A Step-by-Step Overview to Installing a Bathtub
Blog Article
They are making a number of great pointers regarding Installing A Bathtub in general in the article which follows.
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall to remove the old tub as well as position the new tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have already bought a new bathtub and also do not need to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist should consist of the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making sure that the washing machines are in area between the tap and also the sink. Secure the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the spirit level reviews level.
To set up taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and also check all joints and new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the tub must wait up until the tub has been utilized a minimum of once as this will settle it right into its last placement.
Planning for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components as well as installations. They are sold in tubes and also cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealant can fracture fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed our article. So long as you liked our page kindly do not forget to pass it around. I enjoy reading our article about Tools You Need to Install a New Bathtub .
Schedule Services
Report this page